Atomic Penny Vaporizer


Marty Sagendorfby: Martin Sagendorf

Imagine students’ amazement when they actually see sunlight melt a penny with the Atomic Penny Vaporizer!  This demonstration clearly illustrates the vast amount of energy illuminating the Earth’s surface.  In rough numbers: 70% of the Sun’s incident energy on our outer atmosphere is reflected back into space – only about 30% actually gets to the Earth’s surface.  But, as we experience, this is still a substantial quantity of energy.

Fortunately, this energy (I. R. – Visible – U. V.) is rather uniformly distributed over the Earth’s surface –  thus its overall intensity is such that we have a habitable environment.  However, as we all know, we can concentrate some ‘area’ of this energy to increase the ‘energy per area’ (a measure of this is the temperature of the area of concentrated energy).  A common magnifying lens (2-4 in. diameter) will concentrate sufficient energy to burn paper or other objects with a low flash point. Read the rest of this entry »


Teaching Observation Skills with a Science Journal


Matthew Campbellby:  Matthew Campbell

One of the more important traits a scientist can have is the ability to observe.  Helping our students become better observers can be tricky.  Observation is a soft-skill and can be difficult to teach directly.  In my experience I also find that students tend to rush through labs to obtain the answer quickly.  This desire for speed is contrary to the pace required for careful, precise observation.

My solution for helping students become better observers is the science journal.  The purpose of the science journal is to encourage students to observe the science happening all around them.  The scope of the project allows for careful observations to be made which can then proceed into conclusions and validations of hypotheses. As an added bonus, the journal integrates literacy into the science classroom.  I encourage my students to select topics that appeal to them to increase investment in the project.

Read the rest of this entry »


Cartesian Divers


Ron Perkins, Educational Innovationsby: Ron Perkins

Cartesian Divers are one of the oldest and most interesting toys you can build at home.  While they are easy to construct, there is a lot of science behind the workings of this deceivingly simple toy.  A Cartesian Diver is an object whose density changes with pressure.  In fact, most Cartesian divers become denser as pressure is increased.  By constructing a Cartesian Diver carefully, it is possible to make a diver that floats in water at atmospheric pressure, and sinks when the pressure is increased.

Water has a density of about 1 gram/ml.  Objects that have a density of less than 1 gram/ml float, while objects with a density greater than 1 gram/ml sink.  When using sealed divers, as pressure is increased, a Cartesian Diver’s density might increase from about .8 grams/ml to 1.2 grams/ml.  When this happens, the diver sinks in water.  Cartesian Divers often change their density by changing the amount of water they displace (i.e., changing their volume).  When the pressure is increased, the air inside the diver is compressed.  This compressed air takes up less space, and thus displaces less water.  As less water is displaced, the density of the diver appears to increase and the diver sinks.

Making Cartesian Divers

Materials:

1 Plastic Pipet (PP-222), 1 Ballast Nut (CD-3), Plastic Soda Bottle with Top, Candle, Scissors, Pliers, Water

Optional: cap of a Fizz-Keeper Pump (CD-4), Food Coloring, Aluminum Foil, Hot Melt Glue Gun

Instructions

1.  With scissors, snip off all but 2 cm of the neck of the pipet.

Cartesian Divers - Educational Innovations Blog

2.  Screw one ballast nut onto the remaining 2 cm neck of the pipet.

Cartesian Divers - Educational Innovations Blog

Cartesian Divers - Educational Innovations Blog3.  Fill the pipet bulb with colored water.  Note that the bulb must float when placed in a cup of water.  Experiment with different amounts of water, making sure that the bulbs still float.  Bulbs that float higher in a cup of water will make divers that are more difficult to sink.

4.  Your Cartesian diver is ready!  Fill a 1 or 2 liter plastic soda bottle almost to the top with water.  Place your diver in the bottle and screw on the Fizz-Keeper pump cap.  Try squeezing the bottle.  Can you make your diver sink?  Now pump the Fizz-Keeper and watch as your diver sinks right to the bottom.  Can you figure out how to get it back up to the top?

5.  Remove the pump cap, pour out your diver, and try varying its buoyancy.  Try filling it with different amounts of water.  Put it back in the bottle, replace the pump cap and try sinking it again.

6.  When you are satisfied with your divers and would like to make it permanent, you can seal it by sealing the open end of the bulb.  This can be done with any waterproof glue, hot glue, or by melting the plastic stem slightly and squeezing it gently with small pliers.

To seal the bulb by melting, first make sure your bulb floats.  Once it is sealed, its starting buoyancy cannot be changed! Make sure there is no water in the neck by holding it upside down and tapping or squeezing it slightly.  Hold the neck about 1-2 inches above a candle flame until it becomes completely transparent (the change is very subtle).  Immediately remove the neck from above the flame and squeeze the end gently with pliers to seal.  Let cool.  Return your diver to the bottle with clean water and it will last for many years.

There are literally hundreds of experiments you can try!  For instance, try crumpling up a piece of aluminum foil into a small ball.  Place this in your bottle.  See if you can sink it by squeezing the bottle… how about pumping it?  Small packets of soy sauce have also been known to work!

Use more pipets and vary their densities.  Try numbering your divers and see if you can make them sink in order.  Note that your divers are not yet sealed, and so they can be adjusted as many times as you like (colored water will leak out of them until they are sealed).

Educational Innovations carries a full line of Cartesian Diver materials, including Bob Becker’s DVD that demonstrates and discusses a plethora of fascinating diver designs.  Bob Becker, an award winning high school chemistry teacher, is a pioneer in the field of Cartesian divers.  This DVD includes DVD-ROM which contains additional resources such as project guides and templates.


The Amazing Drinking Bird


Tami O'Connor, Educational Innovationsby Tami O’Connor

Invented in 1945 by Miles Sullivan, the “drinking bird” has been a favorite of science teachers in every classroom from kindergarten through college. This amazing device is made of two glass bulbs (one representing the head and the other representing the body) joined by a glass tube (representing the neck).  Between the two bulbs, attached to the glass tube, is a metal fulcrum upon which the bird pivots.  The air has been removed from this closed device, and the bottom ball is filled with a colored liquid that has a high vapor pressure (methylene chloride). The rest of the bird’s body and head is filled with the vapor form of methylene chloride.

Read the rest of this entry »


Ammonite, The Fibonacci Fossil!


Sarah Brandtby: Sara Brandt

Ammonite was once thought to be the petrified remains of snakes! Modern science, however, tells us that these fascinating fossils are actually the remains of an ancient aquatic mollusk.  A mollusk is an invertebrate with a soft, unsegmented body.  The soft body of an ammonite was protected by a hard outer shell. The shells of ammonites ranged from an inch to nine feet! Each shell is divided into many different chambers. The walls of each chamber are called septa. The septa were penetrated by the ammonite’s siphuncle, a tube-like structure that allowed the ammonite to control the air pressure inside its shell. Ammonites were aquatic creatures, and being able to control the air pressure inside their shells meant being able to control their buoyancy.

What is the Fibonacci sequence?

Read the rest of this entry »